top of page
Search

Vessel Wall Thickness: Formulas, Heads and a Worked Example

5 days ago
10 min read

Technician measuring a pressure vessel head

The required wall thickness of a pressure vessel comes from the design pressure, the inside radius or diameter, the allowable stress of the material at design temperature, and the weld joint efficiency. For a cylindrical shell under internal pressure, ASME Section VIII Division 1 gives t = PR/(SE − 0.6P). Heads use related formulas, and you then add corrosion allowance and mill tolerance to get the thickness you order. Below is the full routine, with a worked example you can rebuild in a spreadsheet, including the reverse calculation for maximum allowable working pressure.



TL;DR

 

  • Shell: t = PR/(SE − 0.6P). A 2:1 ellipsoidal head: t = PD/(2SE − 0.2P). A hemispherical head is the thinnest of the common shapes.

  • Required thickness is not the ordered thickness: add corrosion allowance and check mill under-tolerance, then round up to available plate.

  • External pressure (vacuum) can govern the shell. Check it separately; it is a stability problem, not a stress problem.

  • MAWP is the reverse calculation: the highest pressure the weakest component can carry at design temperature, in its corroded condition.

  • Always state your assumptions (S, E, CA, temperature) next to the result so someone else can check it.

 

Table of Contents

 

 

What the wall thickness calculation really answers

 

The formulas answer one question: how thin can this component be and still hold the design pressure with the safety margin the code builds into the allowable stress? They do not decide the material, the fabrication method or the inspection level. ASME’s own guidebook for Section VIII treats thickness as one part of a chain that includes materials, fabrication, inspection affecting joint efficiencies, testing, and shells, heads and transition sections under internal and external pressure.

 

That is why the same pressure and diameter can give different thicknesses on two projects. Inspection level changes E, material and temperature change S, and service changes the corrosion allowance. If you are a student, treat the thickness formula as the end of a list of decisions, not the beginning.

 

This article uses ASME Section VIII Division 1, the most common U.S. code for unfired pressure vessels, and US customary units. If your vessel falls under another code (Division 2, EN 13445, or a local rule), the structure is the same but the equations and allowable stresses differ. Confirm the current edition and any jurisdictional rules before issuing a design.

 

The inputs you need before you start

 

Every thickness calculation uses the same short list of inputs. Write them down first.

 

Symbol

Meaning

Where it comes from

P

Design pressure, including static head of liquid where it matters

Process requirements plus a margin above operating pressure

R or D

Inside radius or inside diameter (corroded condition for a rigorous check)

Vessel layout

S

Maximum allowable stress at design temperature

Section II Part D tables for the chosen material

E

Joint efficiency

Weld type and extent of radiography

CA

Corrosion allowance

Service and expected life

t

Minimum required thickness

The result

Two inputs cause most student errors. First, S is read at the design temperature, not room temperature, and it drops as temperature rises. Our temperature-first guide to vessel material selection shows how to pick the material before you look up S. Second, E is not a free choice: it depends on the weld category and how much of it is examined. The difference between 0.85 and 1.0 is large enough to change the plate you buy, and we cover it in our guide to ASME joint efficiency.

 

Cylindrical shell thickness under internal pressure

 

For a cylinder, the governing stress is the circumferential (hoop) stress, which is twice the longitudinal stress. UG-27 expresses the hoop requirement as t = PR/(SE − 0.6P), with R the inside radius, S the allowable stress and E the joint efficiency. The 0.6P term is a correction that moves the result toward the thick-wall answer; it is small for thin vessels and matters more as pressure rises relative to SE.

 

The longitudinal (axial) check, which also appears in UG-27, uses a different form and usually governs only when the circumferential joint has lower efficiency than the longitudinal one or at high pressure. Calculate both and keep the larger.

 

These equations are thin-wall formulas. They hold for moderate wall-to-radius ratios and pressures. If your pressure is very high relative to the allowable stress, or the wall is thick compared with the radius, you leave the range of UG-27 and need the thick-wall rules or a Division 2 approach.

 

Vessel head thickness: one pressure, different shapes

 

Heads close the ends of the shell, and their shape changes how much metal they need. For internal pressure, the common ASME VIII-1 equations are:

 

Head type

Required thickness

Cylindrical shell (for comparison)

t = PR/(SE − 0.6P)

2:1 semi-ellipsoidal

t = PD/(2SE − 0.2P)

Torispherical (flanged and dished)

t = 0.885PL/(SE − 0.1P)

Hemispherical

t = PL/(2SE − 0.2P)

Here D is the inside diameter and L is the inside crown radius (for a hemisphere, the inside spherical radius). Bolted flat heads use a separate method with attachment-dependent factors, not one of the equations above. For torispherical heads, the 0.885 factor applies to the standard proportions with a knuckle radius of 6% of the crown radius; heads with other proportions use a different factor, so read UG-32 against your geometry. Our article on the six pressure vessel head types, with ASME rules and FEA checks walks through each shape.

 

What the numbers look like

 

In a published 420 psi comparison, a hemispherical head needed 0.2474 in, a 2:1 semi-elliptical head 0.4947 in and a flanged-and-dished head 0.8901 in, against 0.5 in for the cylinder. The pattern is the useful part. A hemisphere carries pressure most efficiently, but it is deep and costly to form. A 2:1 ellipsoidal head is shallower and typically lands near the shell thickness. A torispherical head is shallowest and generally needs the most thickness.

 

So head choice is a trade between plate thickness, forming cost and available height, not a search for the thinnest head.

 

Worked example: shell, head and MAWP

 

This example is illustrative. The inputs are chosen for simple arithmetic, not taken from a design basis. Rebuild it in a spreadsheet to check your own method.

 

Inputs: design pressure P = 300 psi, inside diameter D = 48 in (R = 24 in), S = 20,000 psi at design temperature, E = 0.85 (spot radiography), corrosion allowance CA = 0.0625 in.

 

Step 1. Shell. t = PR/(SE − 0.6P) = (300 × 24)/(20,000 × 0.85 − 0.6 × 300) = 7,200/16,820 = 0.428 in. Add corrosion allowance: 0.428 + 0.0625 = 0.490 in.

 

Step 2. 2:1 ellipsoidal head. t = PD/(2SE − 0.2P) = (300 × 48)/(2 × 20,000 × 0.85 − 0.2 × 300) = 14,400/33,940 = 0.424 in. Add corrosion allowance: 0.424 + 0.0625 = 0.487 in.

 

The head and shell come out close, which is typical for a 2:1 head. If the head were seamless and E could be taken as 1.0, the same equation gives 14,400/39,940 = 0.361 in. The joint efficiency of a formed head follows its own weld rules, so read the code for each component rather than reusing the shell’s E.

 

Step 3. Choose the plate. Suppose you order 9/16 in (0.5625 in) plate. Check that this nominal thickness, less mill under-tolerance and any forming thinning, still exceeds the required thickness plus corrosion allowance.

 

Step 4. MAWP of the shell. Turn the formula around for the corroded thickness: P = SEt/(R + 0.6t). With t = 0.5625 − 0.0625 = 0.5 in: P = (20,000 × 0.85 × 0.5)/(24 + 0.6 × 0.5) = 8,500/24.3 = 350 psi.

 

That is the shell’s MAWP in this example. Compute the same for the head and every other pressure part, then take the lowest. The 350 psi is higher than the 300 psi design pressure, which is the margin from rounding up to standard plate.


Worked shell and head thickness calculations

Add the allowances: corrosion, tolerance and forming

 

The formula gives a minimum. The thickness you order must cover three more things.

 

Corrosion allowance. This is extra metal added for expected loss in service. It depends on the fluid, temperature, and design life, and it can differ between shell, heads and nozzles. We cover how to choose it in our ASME and API playbook for corrosion allowance.

 

Mill under-tolerance. Material can be delivered below nominal thickness. Guidance on Section VIII UG-16 describes a 12.5% under-tolerance for pipe, which gives t(nominal) ≥ (t(required) + CA)/0.875 for that case. Plate follows its own specification, so check the plate standard rather than carrying one tolerance over to every product.

 

Forming thinning. Dished heads thin during forming, especially at the knuckle. The head you specify must still meet the minimum after forming, which is why receiving inspection with thickness measurement is recommended in construction guidance.

 

Also apply the code minimum thickness for the construction, and remember that nozzle openings, supports and attachments each need their own checks. The shell formula does not cover them.

 

When external pressure sets the thickness

 

A vessel under vacuum or external pressure can fail by buckling long before the material yields. UG-28 and UG-33 give a separate stability check. Resistance depends on diameter, length, thickness, yield strength and elastic modulus, so adding stiffening rings or thickness raises it, while larger diameter or length lowers it.

 

The same source’s worked example shows how much this can matter. A 48 in diameter, 96 in straight shell needed 0.056 in for 30 psi internal pressure, but 0.225 in for 15 psig external pressure. Heads under vacuum needed 0.142 in (flanged and dished) and 0.127 in (semi-ellipsoidal). The lower pressure produced the thicker wall.

 

If your vessel sees vacuum during steam-out, cooldown or upsets, run this check before you finalize the plate. Our guides on pressure vessel buckling analysis and stress analysis formulas and FEA cover the methods in more depth.

 

Design pressure, MAWP and allowable pressure

 

These terms are often mixed up, and exam questions rely on that.

 

 

The MAWP must not fall below the design pressure for any component. The usual workflow runs forward to choose plate, then backward to confirm what the as-built vessel can hold. Calculate it in the corroded condition for a vessel that will corrode, and recalculate it when the design temperature changes, because S changes with temperature.

 

Common mistakes that change the answer

 

  1. Using room-temperature allowable stress. The result is unconservative at high temperature.

  2. Mixing inside and outside dimensions. The UG-27 forms above use inside radius.

  3. Forgetting static head on tall liquid-filled vessels.

  4. Applying the shell E to every head. Check the weld category and examination for each part.

  5. Ignoring vacuum. The internal-pressure answer may be a fraction of the external-pressure answer.

  6. Reporting only the final thickness. State S, E, CA, temperature and code edition so the check can be repeated.

 

How we approach this at Jewlz

 

We build our engineering tools around a simple belief: a thickness number is only as good as the assumptions you can see. Our toolkit combines conduction, convection and radiation models with a built-in property database, so material properties across a wide temperature range sit in the same place as your calculation.   For pressure vessels, that means you can move from a hand calculation to a simulation without re-keying inputs, and then check how temperature fields feed back into the stresses that set your wall. Our Excel-based toolkit is designed so small teams and students can run professional thermal and pressure vessel analyses without a licensing barrier.   Start with the code formula, as above. Then use simulation to look at what the formula cannot see: thermal gradients, local stresses and fluid behavior around the vessel.   Joel

 

Put your wall thickness check into a toolkit

 

The Jewlz Engineering Toolkit includes pressure vessel simulation, thermal analysis and heat transfer, CFD and fluid flow simulation, and heat exchanger design optimization, in a downloadable Excel-based tool with a built-in property database. It supports variable material properties and multiple heat transfer modes across a wide temperature range.


Jewlztech

See the pressure vessel simulation and the rest of the toolkit, or start from the Jewlz Engineering Toolkit home page. If your vessel holds cryogenic liquid, the cryogenic pressure vessel and boil-off simulator adds boil-off behavior to the picture.

 

From formula to a design you can defend

 

Once the thickness is set, the temperature field matters. Our guide to a practical finite element thermal workflow for pressure vessels shows how thermal loads enter the stress picture. For cyclic service, the fatigue analysis guide covers the next check, and the insulation guide covers the heat-loss and corrosion-under-insulation side.

 

A vessel that will be stamped must be designed and certified under the applicable code and jurisdiction, with the design reviewed by a qualified engineer. The calculations in this article are for learning and for checking your own work.

 

FAQ

 

How do I calculate the wall thickness of a pressure vessel?

 

Collect design pressure, inside radius, allowable stress at design temperature and joint efficiency. For a cylindrical shell under internal pressure, apply t = PR/(SE − 0.6P), then add corrosion allowance and cover mill under-tolerance. Check external pressure separately if the vessel sees vacuum.

 

What is the formula for vessel head thickness?

 

For a 2:1 ellipsoidal head under ASME VIII-1, t = PD/(2SE − 0.2P). A hemispherical head uses t = PL/(2SE − 0.2P), and a standard torispherical head uses t = 0.885PL/(SE − 0.1P). Hemispherical heads need the least thickness, torispherical heads the most.

 

What is the maximum allowable pressure formula for a cylindrical shell?

 

Rearrange the thickness equation: P = SEt/(R + 0.6t), where t is the corroded thickness. Calculate the same for the heads and other pressure parts. The lowest value is the vessel’s MAWP at that temperature.

 

What is the difference between design pressure and MAWP?

 

Design pressure is the input used to find minimum thickness. MAWP is the output: the highest pressure the completed vessel can carry at design temperature. MAWP should never be lower than the design pressure for any component.

 

Sources

 

Recommended

 

 
 
 

Comments


logo

© 2026 by Jewlz Technologies.

bottom of page